Plumbing 101: Tips for Bathtub Installation
Plumbing 101: Tips for Bathtub Installation
Blog Article
Just how do you feel in regards to Installing A Bathtub?
Setting up a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a moderately challenging project. If the old bathtub is readily obtainable, the task can move speedily; if you have to open up a wall surface to remove the old bathtub as well as place the new bathtub, the task is much harder. In either instance, the task is within a residence handyman's abilities, although you will require a helper to move out the old bathtub as well as embeded in the new one. Ensure you have actually qualified on your own for the work and also fit attempting it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to think about utilizing one prior to you start. Chances are you may require a professional plumber to make tube connections.
This post will certainly assist you set up a new tub in your shower room if you have already bought a new tub and also don't need to alter the arrangement of your previous supply of water pipes.
Your devices as well as material checklist should consist of the following:
Preparing for the Setup
To start with, the sustaining structure supplied with the bath ought to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be suited its final position.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite bothersome due to the limited accessibility that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipelines. When the supply pipelines have been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Before carrying on to fit the new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Using both wooden boards under its feet, position the bath tub in the required position. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the tub till the level reads degree.
To install faucets, fit all-time low of the outermost versatile tap adapter to the proper supply pipe by making a compression join; then do the same for the other tap.
Activate the supply of water and also inspect all joints and also brand-new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as additionally examine the overflow outlet and also the regular outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bath tub must wait till the bathtub has actually been used at the very least when as this will settle it into its last placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will need a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making certain that the washers are in area in between the faucet and also the sink. Secure the tap in position with the producer offered backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The former type should be linked to the faucet ends first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to crack an inflexible seal, causing the water to penetrate the wall surface between the bath as well as the tiling, leading to difficulties with wetness as well as possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components as well as installations. They are sold in tubes and also cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to permit the movement experienced when the tub is in use. The sealant can fracture rather very early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly offered on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that write-up about How to Install a Bathtub through a good friend on a different domain. Sharing is nice. Who knows, you will be helping someone out. Many thanks for going through it.
Dial, we deliver! Report this page